Material Witness: R.I.P. Speedboard C


Reading time ( words)

Material Witness by Chet Guiles

When W. L. Gore recently announced plans to discontinue their Speedboard® C product, it created a bit of a stir in the marketplace. Here was a product that was unique and versatile and that, for many of us in the laminates business, made possible the use of our materials in applications that otherwise could have been problematic. Those of us who have been in the industry for more than a couple of years know that products, even good ones, come and go for a variety of technical and business reasons. Just as materials need to meet applications with "fit, form and function," the same kinds of criteria determine the fit of a given product for a business segment. Another example of a very good product being discontinued is the demise of the DuPont Thermount® product a few years back. That, too, created a bit of furor in the industry, but in the end in that case as in the case of Speedboard C we have to bite the collective bullet and find a way to move on.

What is it that the industry found so useful about the Speedboard C product? Because it was made using W. L. Gore's unique expanded PTFE fibers in the base fabric, with a formulated low dielectric constant thermoset resin system, the product was very useful in bonding together a variety of microwave and RF products where dissimilar and hard to bond layers of materials (such as Teflon laminates) needed to be multi-layered into a complex design. The key properties in this writer's mind were the low dielectric constant and reasonable loss, combined with the fact that it was a high-Tg (220°C) thermoset system that stuck well to a variety of materials. This combination is not easy to achieve and without the boost from the proprietary low Dk expanded PTFE reinforcement, replacing it represents something of a conundrum for the industry.

What does a product need to be and do to be useful in the sorts of applications that used Speedboard® C? As a minimum:

  • Low dielectric constant for high signal speeds;
  • Dielectric constant stable over a range of frequencies;
  • Low loss for optimized signal integrity;
  • Excellent adhesion to PTFE and other microwave/RF cores;
  • Processable in standard Lamination cycles; and
  • Good peel strength to standard copper foils.

What are the limitations in achieving Speedboard C Properties?

Speedboard C was a unique product based on a formulated cyanate ester resin system coated on WL Gore's proprietary expanded PTFE reinforcement. This resulted in excellent dielectric constant (2.6), good loss (0.004) and a high Tg (220°C) resin system compatible with lead-free fabrication. Full Tg development was obtainable using a cure temperature over 200°C (typical for polyimide and cyanate ester resins), though the product could be cured at lower temperatures (high Tg epoxy cures typically at 380°C) albeit with a lower Tg development.

The higher water absorption typical of cyanate ester resin systems is an issue in microwave systems, since water has a high dielectric constant (about 70) and is highly polar, which means that both Dk and df can be significantly affected at higher frequencies.

No replacement material will be Speedboard C, but an alternative offering from Arlon approximates the important electrical properties with the advantage of a much lower loss (0.002 versus 0.004 for the Speedboard C resin system) and significantly reduced water absorption. A ceramic-filled two-part resin system, the GenCladTM 280 product has lower X-Y CTE for improved registration stability and a high decomposition temperature which makes it usable in PTFE fusion-bonding lamination cycles. The ceramic component helps stabilize the Dk over temperature and the low thermal coefficient of dielectric constant is comparable to many filled PTFE products A comparison of key values for GenClad 280 and Speedboard C are shown in the following table:


* Dk values are not reported on comparable test methods.

So what are the trade-offs? And how will they impact performance?

Share




Suggested Items

A Focus on Process Control, Part 1

09/27/2022 | I-Connect007 Editorial Team
Michael Carano is a noted subject matter expert with respect to process control, electroplating and metallization technology, surface finishing, and reliability. So, it was only natural that we sat down to talk about mechanizing an existing facility given today’s fickle environment. Will any of the CHIPS funding trickle down to bare board fabrication? What process can be adjusted on the factory floor? The focus needs to be more than just on manufacturing and getting work out the door, he says, but also process control.

I-Connect007 Editor’s Choice: Five Must-Reads for the Week

08/05/2022 | Nolan Johnson, I-Connect007
The Top 5 list this week contains industry analysis from IPC’s Shawn DuBravac, news on the passage of the U.S. “CHIPS Plus” bill, new materials from Ventec, news about a fab for sale, and a chemistry company completing their acquisition, plus a brand new book in the I-Connect007 eBooks series.

PCB Finance Class With Jeff De Serrano

07/28/2022 | Nolan Johnson, I-Connect007
Class is in session! PCB Technologies President Jeff De Serrano takes us through some of the struggles of the PCB industry over the past 30 years, how U.S. legislation seeks to level the playing field, and whether a “monopoly” of fabricators is healthy for our industry. In his chat with Nolan Johnson, Jeff gets out his investment playbook and talks strategy. Don’t miss this one.



Copyright © 2022 I-Connect007. All rights reserved.